Get A Free Estimate

 

 

Almost everyone seems to have their own unique piece of advice on the subject of A Step-by-Step Guide to Installing a Bathtub.

Setting up a bathtub isn't specifically rocket science, but it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably tough project. If the old bathtub is easily accessible, the task can move easily; if you have to open a wall surface to remove the old bathtub and place the new bath tub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will certainly need an assistant to leave the old tub as well as set in the brand-new one. Make certain you have certified yourself for the work as well as are comfortable trying it. Instead of working with a specialist to take over a halfway-completed task, it is much better to consider utilizing one before you start. Chances are you might need an expert plumber to make tube links.
This article will certainly aid you set up a brand-new bath tub in your restroom if you have actually already purchased a brand-new tub as well as do not require to change the plan of your previous water pipes.
Your devices and also material list need to comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Removing Old Taps

If you need to change old taps with new ones as a part of your setup, after that the first thing you should do is detach the water system. After doing so, activate the taps to drain any kind of water continuing to be in the system. The process of eliminating the existing taps can be rather bothersome as a result of the restricted gain access to that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the staying water that will originate from the pipelines. As soon as the supply pipes have been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning during this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing compound.
Before proceeding to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.

 

 

Fitting New Taps

If the tails of the new taps are plastic, then you will need a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin ensuring that the washers are in place between the tap and the sink. Secure the tap in place with the producer supplied backnut. When the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal faucet adapters. The previous kind should be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

 

 

Mounting the Bath tub

Making use of both wood boards under its feet, place the bathtub in the required position. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the tub up until the spirit level checks out level.
To set up taps, fit the bottom of the furthest flexible tap connector to the appropriate supply pipe by making a compression join; then do the same for the various other faucet.
Activate the water and also examine all joints and also brand-new pipework for leaks as well as tighten them if required. Fill the bathtub and additionally examine the overflow electrical outlet and also the typical outlet for leaks.
Finally, fix the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub needs to wait till the tub has been used at least when as this will certainly settle it into its final placement.

 

 

Planning for the Setup

Firstly, the supporting structure provided with the bath should be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the faucet comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to stop stress on the bath tub.
Fit the versatile tap ports to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now be ready to be suited its final setting.

 

 

Tiling Around the Bath tub

In the area where the bath satisfies the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to break a stiff seal, creating the water to penetrate the wall surface between the bath as well as the tiling, bring about complications with moisture and also feasible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures as well as installations. They are marketed in tubes as well as cartridges, and also can securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the tub with water prior to securing, to permit the movement experienced when the tub is in usage. The sealer can crack fairly early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I was shown that editorial about Installing A Bathtub through someone on our other web blog. Do you know about another individual who is curious about How to Install a Bathtub? Why not share it. Many thanks for your time invested reading it.

Schedule Free Estimate